Configuring Static Public IP Communication

If your terminal will communicate with the Moneris Host over the Internet using Public IP with Static addressing, you will need to set up these parameters.

Note:  If the terminal is configured to use Ethernet communication and dial backup is available,  when Ethernet communication is not available the terminal will attempt to use dial communication. After performing a transaction using dial (as backup), the terminal will attempt to use Ethernet communication for the next transaction.

Before you begin you will need:

• the terminal's IP Address

• the terminal's Mask ID

• the terminal's Gateway Address

• the terminal's Primary DNS Address

• the terminal's Secondary DNS Address

Note:  If you are configuring the terminal to work as a semi-integrated device with your ECR, you will also need to know the Port number that the ECR is configured to use to communicate with the terminal.

From the READY screen (or the TERMINAL SETUP REQUIRED or REINITIALIZATION REQUIRED prompt):

Note:  The Ethernet cable must be connected before the terminal can communicate with the Moneris Host.

To navigate through the menus:

- Scroll down: press the key to move the highlight bar down.
- Scroll up: press the key to move the highlight bar up.
- Select a highlighted item: press the  key.

For information about the keys...

1. Set the Host parameters to Public

2. Select the Communications Type

a.  Press the  key.
The MAIN MENU appears.

b.  Scroll down to CONFIGURATION, and press the  key.
The CONFIG FUNCS menu appears.

c.  Scroll down to GENERAL PARAMS, and press the  key.
The GENERAL PARAMETERS menu appears.

If the SWIPE ADMIN CARD prompt appears, swipe the POS admin card.

d.  Press the  key to select COMMS TYPE.
The COMMUNICATION TYPE menu appears.

e.  Scroll to ETHERNET, and press the  key.
The ETHERNET SETUP menu appears.

Note:  You may need to press the key once then scroll down to and select ETHERNET CFG to access the ETHERNET SETUP menu.

3. Set up the Terminal Type as Static

a.  Press the  key to select TERMINAL SETUP.
The TERMINAL SETUP menu appears.

b.  Press the  key to select TERMINAL TYPE.
The TERMINAL TYPE menu appears.

c.  Scroll to STATIC, and press the  key.
The TERMINAL SETUP menu reappears.

d.  Scroll down to TERMINAL ADDR, and press the  key.
The ENTER TERMINAL ADDRESS entry screen appears.

e.  Key in the terminal's IP Address, and press the  key. ( Entering alphabetic characters and punctuation )
The TERMINAL SETUP menu reappears.

f. Scroll down to MASK ID, and press the  key.
The ENTER MASK ID entry screen appears.

g. Key in the terminal's Mask ID, and press the  key. ( Entering alphabetic characters and punctuation )
The TERMINAL SETUP menu reappears.

h. Scroll down to GATEWAY, and press the  key.
The ENTER GATEWAY ADDRESS entry screen appears.

i. Key in the Gateway Address, and press the  key. ( Entering alphabetic characters and punctuation )
The TERMINAL SETUP menu reappears.

j.  Do one of the following:
If you are setting up a standalone terminal (with or without an external PINpad): Skip this step, and go directly to step k.  
OR
If you are setting up the terminal to work as a semi-integrated device with your ECR:

i.  Scroll down to PORT NUMBER, and press the  key.

ii.  key in the Port Number that the ECR is using to communicate with the terminal, and press the  key.
The TERMINAL SETUP menu appears.

k.  Press the  key once.
The ETHERNET SETUP menu appears.

4. Set up the DNS Addresses

a. Scroll down to DNS SETUP, and press the  key.

Note:  If the AUTOMATIC DNS item appears instead of the PRIM ADDRESS and SEC ADDRESS items, select AUTOMATIC DNS then press the key.

b. Scroll down to PRIM ADDRESS, and press the  key.
The ENTER PRIMARY ADDRESS entry screen appears.

c. Key in the Primary DNS Address, and press the  key. ( Entering alphabetic characters and punctuation )

d. Scroll down to SEC ADDRESS, and press the  key.
The ENTER SECONDARY ADDRESS entry screen appears.

e. Key in the Secondary DNS Address, and press the  key. ( Entering alphabetic characters and punctuation )

5. Test the connection to the Moneris Host

a. Press the key once.
The REBOOT TERMINAL message appears and then the terminal reboots.

b. When the READY screen (or TERMINAL SETUP REQUIRED or REINITIALIZATION REQUIRED) appears, press the  key twice, key in 13, and press the key.

c. Press the key to test the connection.
The TCP HOST CONNECTION OK PRESS OK prompt appears if the connection is up.

d. Press the key to return to the READY screen (or TERMINAL SETUP REQUIRED or REINITIALIZATION REQUIRED).

e.  If you are configuring the terminal for the first time, go back to "Configuring Communications."

Note: You must perform a re-initialization to complete the configuration process.

The terminal is ready to communicate with the Moneris Host over the Internet.