Configuring Static Public IP Communications

IMPORTANT:  Do NOT attempt to configure your terminal without assistance from the Moneris Merchant Service Centre.

If your terminal will communicate with the Moneris Host over the Internet using Public IP with Static addressing, you will need to set up these parameters.

Each handheld terminal must have its own unique IP address assigned to it.

Note:  If the terminal is configured to use Ethernet communications and dial backup is available,  when Ethernet communication is not available the terminal will attempt to use Dial Communications. After performing a transaction using dial as backup, the terminal will attempt to use Ethernet Communications for the next transaction.

Before you begin you will need:

• the terminal's IP Address

• the terminal's Mask ID

• the Gateway Address

• the Primary DNS Address

• the Secondary DNS Address

From the READY screen or the TERMINAL SETUP REQUIRED prompt:

Note:  The Ethernet Communications cables must be connected before attempting to communicate with the Moneris Host.

To navigate through the menus:

- Scroll down: press F1 to move the highlight bar down.
- Scroll up: press F3 to move the highlight bar up.
- Select a highlighted item: press OK.

If you access a prompt and decide to keep the displayed value, simply press OK to keep that value and return to the previous menu.

1. Select the Communications Type

a.  Press the Admin key.
The MAIN MENU appears.

b.  Scroll down to CONFIGURATION, and press OK.
The CONFIG FUNCS menu appears.

c.  Scroll down to GENERAL PARAMS, and press OK.
The GENERAL PARAMETERS menu appears.

If the SWIPE ADMIN CARD prompt appears, swipe the POS Admin card.

d.  Press OK to select COMMS TYPE.
The COMMUNICATION TYPE menu appears.

e.  Scroll to ETHERNET, and press OK.
The ETHERNET SETUP menu appears.

Note:  You may need to press Can/Ann once then scroll down to and select ETHERNET CFG to access the ETHERNET SETUP menu.

2. Set up the Terminal Type as Static

a.  Press OK to select TERMINAL SETUP.
The TERMINAL SETUP menu appears.

b.  Press OK to select TERMINAL TYPE.
The TERMINAL TYPE menu appears.

c.  Scroll to STATIC, and press OK.
The TERMINAL SETUP menu reappears.

d.  Scroll down to TERMINAL ADDR, and press OK.
The ENTER TERMINAL ADDRESS entry screen appears.

e.  Key in the terminal's IP Address, and press OK. (Entering alphabetic characters and punctuation)
The TERMINAL SETUP menu reappears.

f. Scroll down to MASK ID, and press OK.
The ENTER MASK ID entry screen appears.

g. Key in the terminal's Mask ID, and press OK. (Entering alphabetic characters and punctuation)
The TERMINAL SETUP menu reappears.

h. Scroll down to GATEWAY, and press OK.
The ENTER GATEWAY ADDRESS entry screen appears.

i. Key in the Gateway Address, and press OK. (Entering alphabetic characters and punctuation)
The TERMINAL SETUP menu reappears.

j. Press Can/Ann once.
The ETHERNET SETUP menu reappears.

3. Set up the Host Parameters as Public

Note: If you change any of the Host parameters after the terminal has been initialized, the terminal will prompt you to perform a re-initialization.

a. Select HOST SETUP.

The ETHERNET SETUP menu reappears.

4. Set up the DNS Addresses

a. Scroll down to DNS SETUP, and press OK.

Note:  If the AUTOMATIC DNS item appears instead of the PRIM ADDRESS and SEC ADDRESS items, select AUTOMATIC DNS then press F3.

b. Scroll down to PRIM ADDRESS, and press OK.
The ENTER PRIMARY ADDRESS entry screen appears.

c. Key in the Primary DNS Address, and press OK. (Entering alphabetic characters and punctuation)

d. Scroll down to SEC ADDRESS, and press OK.
The ENTER SECONDARY ADDRESS entry screen appears.

e. Key in the Secondary DNS Address, and press OK. (Entering alphabetic characters and punctuation)

5. Test the Ethernet Connection

a. Press Can/Ann twice to test the connection.
The TCP HOST CONNECTION OK PRESS OK prompt appears if the connection is up.

b. Press OK to return to the READY screen.

Note: If the RE-INITIALIZATION REQUIRED message appears, you must perform a re-initialization to complete the configuration process.

The terminal is ready to communicate with the Moneris Host over the Internet.

Go back to Configuring Your Terminal.